2009 (2)
2010 (1)
2014 (58)
2015 (74)
2016 (71)
2017 (67)
2018 (37)
2020 (57)
2021 (47)
2022 (69)
2023 (45)
1. 05 Lexus GS300
1.1 ignition key
VIN: JT8BD69S150204624 key 41403, 51113, 13513
https://www.remotesunlimited.com/specify.php?search=1&type=fcc&search_fcc=HYQ1512V
http://www.keylessremotewarehouse.com/lexus_oem_lexus_fcc_id_hyq1512v_keyless_remote_entry_clicker_w_1_5_new_key_pre_owned_w_new_key_276aa_c_p538.htm
https://www.keylessentryremotefob.com/searchresults.asp?Search=Lexus&Search=2005&Search=GS300
1.2. tire key
Overtigen will crack tire key. my GS300 2005 spec is:
85996, 00623 55501, PT276-30986, orange, Julian dat 16704
1.3. Ignition key programming
https://www.remotesremotes.com/2005-Lexus-GS-300-Keyless-Remote-Key-Fob-Clicker-s/4455.htm
http://www.keymachine.com/images/ilco/SDDTOYLEX.pdf
1. Close and lock all doors. Unlock and open drivers door.
2. Put key into ignition and remove. Do not turn it on.
3. Using the electric lock switch. Lock and unlock 5 times. (Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock)
4. Close and open drivers door.
5. Using the electric lock switch. Lock and unlock 5 times. (Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock)
6. Put key into ignition. Turn to "ON" then "OFF" in one second, remove the key.
7. You will see the door locks cycle once. If not repeat 1-7
8. On the remote, press and hold the LOCK and the UNLOCK button at the same time for no more than 2 seconds.
9. On the remote, press the LOCK button for no more than 1 second.
AT THIS POINT, the locks should cycle by themselves ONE time. This means the procedure was accepted; IF the locks cycle twice it has failed.
The most common reason for programming failure is because the car didn’t receive a good signal from the remote. To fix this problem try these tips. 1) Stand outside of the car while you are performing steps 8 and 9. 2) Don’t hold the remote buttons down as long.
As long as the car is still in programming mode you can keep trying steps 8 and 9 until you complete the programming. If you wait too long and the car exits the programming mode then you must start over.
After you get the remote to program then continue on with step 10.
10. Close and open door to end programming procedure.
1. Insert an already programmed master key into the ignition. Do not turn.
2. Press and release the gas pedal 5 times.
3. Press and release the brake pedal 6 times.
4. Remove the key from the ignition.
5. Insert the new key you want to program into the ignition.
6. Press and release the gas pedal one time.
7. Wait 1 minute. The security light will be blinking for this one minute. When it stops blinking your key is programmed. To end programming step on brake one time.
NOTE: Look for your security light. This light will guide you during the programming procedure. The security light will go off at Step 1. It will remain off until Step 6. The security light will come on and start to blink after Step 6 until the key is programmed. If the security light comes on after Step 4 STOP the procedure and start over again.
If you perform this procedure too slowly your car will not go into programming mode. If you can not get your car to go into programming mode make sure you are using a master key and not a valet key. If you have a master key then you will probably need to perform this procedure more quickly.
1. Open driver door, keep it open and in the unlocked position (all other doors should be closed)
2. Put original key in ignition and pull out
3. Lock and Unlock the doors 5 times (complete each lock/unlock cycle within 1 second and
entire process in 40 seconds or less)
4. Close the door and open the door
5. Lock and Unlock the doors another 5 times (complete each lock/unlock cycle within 1 second and
entire process in 40 seconds or less)
6. Put the key in the ignition, turn it to "on" and then off (with 1 second) and remove from the ignition.
7. Press and hold transmitter LOCK and UNLOCK buttons simultaneously for at least 1.5 seconds,
and then within 3 seconds; press any transmitter button for at least one second.
8. If within 3 seconds, door locks cycle one time, new transmitter code was accepted. If door locks
cycle 2 times, new transmitter code was not accepted. If code was not accepted retry step 8 again.
89070-53531
FCC ID:HYQ1512V https://fccid.io/HYQ1512V
2002-2003 ES300 1998-2005 GS300
2001-2005 IS300 1998-2000 GS400
1998-2000 LS400 2001-2005 GS430
FCC ID:HYQ1512V
2003 - 2008 LX470
2003 - 2009 GX470
FCC ID:HYQ1512V
1998-2002 LX470
FCC ID: HYQ12BBK canada 16511032233 Lexus 89070-24171 https://fccid.io/HYQ12BBK
2003 2004 2005 2006 ES330
2002 2003 2004 2005 2006 SC430
2001 2002 2003 2004 2005 2006 LS430
1999 2000 2001 2002 USA RX300
FCC ID: HYQ12BBT
2007 2008 2009 RX350
2004 2005 2006 RX330
2006 2007 2008 RX400h
314.4MHz
USA Model
FCC ID:HYQ1512V 89785-50031?
1998-2002 LX470
2003 - 2008 LX470
2003 - 2009 GX470
1998-2002 Landcruiser
2.1 編程
遙控器編程隻能用於開關車門不能用於發動車。Transponder編程必須用編程器如Xhorse OBD、CK100+或Honda HDS。兩者的編程步驟：https://www.youtube.com/watch?v=YMQlF4ztrFI#t=5m25s 首先是遙控器Fob編程：關好車門插入舊鑰匙擰至ON，按遙控器鍵再OFF，如此重複３次，在第４次按鍵時車門會自動上鎖再開，再按鍵仍如此。再按新遙控器鍵，關車即可。Transponder編程：CK100+接OBD口，插入舊鑰匙擰至ON，CK100+選Immotolizer及車型，按屏幕提示操作add a key，鑰匙OFF；再ON－OFF；插入新鑰匙ON並在屏幕計數複０前OFF，重複ON-OFF；插入舊鑰匙ON－OFF，再ON，顯示已存儲，按CK100＋任意鍵結束。
