想把摩托的反光鏡拿下來,太緊擰不動,用了flared wrench還是有幾個角stripped,不敢再用力了。噴過WD-40,沒有。有其他穩妥的辦法嗎,不要火攻,容易搞壞其他部件。其實是自己多事追求完美,反光鏡隻是有部分漆有點脫落,想拿下來砂紙打磨一下上新漆,結果更複雜了……
螺絲太緊有點滑絲了,怎麽補救
所有跟帖:
• 用heat gun, harbor freight. 或電吹風。不會燒壞油漆。不用torch。估計有locktite吧 -PrimeryColor- ♀ (0 bytes) () 08/03/2023 postreply 17:14:26
• 一直沒明白heat gun辦法的原理 -DC_Jeeper- ♂ (147 bytes) () 08/03/2023 postreply 17:40:51
• 就是一個大號電吹風。用在這裏熱脹冷縮。 -PrimeryColor- ♀ (0 bytes) () 08/03/2023 postreply 18:56:04
• 有的 loctite 必須加熱才能鬆開,比如一些槍支上的緊固螺絲。汽車上的有些loctite 又是耐熱的。 -Shubin- ♂ (0 bytes) () 08/04/2023 postreply 07:35:58
• Don't use open end fixed wrenches. -jassco- ♂ (229 bytes) () 08/03/2023 postreply 17:48:38
• 謝謝,銼刀先銼平似乎有道理 -DC_Jeeper- ♂ (69 bytes) () 08/03/2023 postreply 18:12:13
• It is caused by -jassco- ♂ (215 bytes) () 08/03/2023 postreply 20:08:37
• 為啥·要拿下了反光鏡? -soccer88- ♂ (0 bytes) () 08/03/2023 postreply 18:35:17
• 覺得拿下來用砂紙磨比較方便,可以磨的很幹淨 -DC_Jeeper- ♂ (0 bytes) () 08/03/2023 postreply 18:48:45
• 工具是對的,選用的尺寸就未必了,緊固件不見得一定是公製或隻能用公製。 -Oneshotkill- ♂ (0 bytes) () 08/03/2023 postreply 18:54:18
• 查了是17mm的,但工具本身可能有點誤差不是嚴絲合縫 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 05:45:34
• 把旁邊遮擋刷油漆不可以嗎? -man008- ♂ (0 bytes) () 08/03/2023 postreply 21:39:47
• 確實可以,當時覺得拿下來很容易 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 05:46:08
• 用管鉗 -TBz- ♂ (0 bytes) () 08/03/2023 postreply 23:13:33
• 我怕這個可能會徹底搞壞底座,空間也不夠 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 05:48:02
• 搜一下這種防滑扳手 -老金工- ♂ (332 bytes) () 08/04/2023 postreply 06:36:52
• 這個Amazon 有賣嗎 -DC_Jeeper- ♂ (784 bytes) () 08/04/2023 postreply 07:41:47
• 用那種鱷魚嘴可以lock的鉗子 -biglow- ♂ (0 bytes) () 08/04/2023 postreply 06:51:20
• 那種會徹底搞壞,做最後的選擇 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 07:43:44
• 可以到網上搜一下解法,還有那個扭矩大約是多少。摩托車震動大,如果擰不了原來那麽緊就討厭了。 -Shubin- ♂ (0 bytes) () 08/04/2023 postreply 07:39:05
• 基本就是這裏提到的幾種辦法,覺得那個防滑扳手有希望 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 07:45:25
• 當然功夫大一點,銼出兩端兩個平麵約15mm高,給15mm開口扳手鬆動也是選項 -老金工- ♂ (247 bytes) () 08/04/2023 postreply 08:24:47
• 很難說,因為那個地方可操作的空間有限,你原來的扳手擰的時候可能與螺帽的平麵有一個角度,所以會擰滑。如果 -Shubin- ♂ (173 bytes) () 08/04/2023 postreply 09:05:25
• 準備換管子吧,切斷管子,上套筒。 -bushihandyman- ♂ (0 bytes) () 08/04/2023 postreply 08:28:51
• 哈哈,原來是反光鏡, 簡單, 別拆了 -bushihandyman- ♂ (0 bytes) () 08/04/2023 postreply 09:03:10
• 簡單的是砸銀子換總成,連刹車油的盒子一起換 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 16:43:07
• 你在鬆鏡子的鎖緊螺母的時候,有沒有用另一隻手反相拉住鏡腿?也可以試試反著擰一下。 -hellotom- ♂ (0 bytes) () 08/04/2023 postreply 09:05:16
• 試了搞不動,不好用力 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 16:46:08
• 沒有必需拆下的必要,不如就此停手,也就是打磨噴漆稍麻煩一點 -mountrobson- ♂ (0 bytes) () 08/04/2023 postreply 09:05:35
• 對,暫時不折騰,收手了 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 16:44:28
• 直接逆時針轉反光鏡柄就可以吧? 不必先鬆開那鎖緊扣 -coorslight969- ♂ (0 bytes) () 08/04/2023 postreply 09:52:56
• 扳不動,太緊了 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 16:40:10
• 見圖。握著反光鏡使勁往回扳 -coorslight969- ♂ (281 bytes) () 08/04/2023 postreply 11:40:33
• 那個螺絲是隨鏡子的,暴力破壞;然後換兩個新的,便宜 -soccer88- ♂ (1132 bytes) () 08/04/2023 postreply 13:40:29
• 擰下來即可,不會破壞,那鎖緊扣和鏡子鎖緊方和放鬆方向是一致的,直接上手搬鏡子。不會損壞任何東西。 -coorslight969- ♂ (0 bytes) () 08/04/2023 postreply 13:54:00
• 懷疑他擰反了方向 -soccer88- ♂ (0 bytes) () 08/04/2023 postreply 13:56:04
• 可能他的扳手滑了,還是別擰了 -chinomango- ♂ (0 bytes) () 08/04/2023 postreply 14:07:47
• 有的摩托車的鏡子螺紋一左一右是反著的。他的圖像是右手的,一般是順時針鎖緊。但內外螺紋易較勁。 -hellotom- ♂ (0 bytes) () 08/04/2023 postreply 15:10:02
• 兩邊螺紋應該是一樣方向的 -DC_Jeeper- ♂ (186 bytes) () 08/04/2023 postreply 16:35:42
• 所以建議你clock方向拉著鏡腿的同時,用扳手counter look方向卸那顆鎖緊螺母。 -hellotom- ♂ (463 bytes) () 08/04/2023 postreply 17:48:06
• 不用管那個螺母,直接推那個鏡子腿,頂多也就是把螺母和車把接觸的地方搞出些痕跡,將來新螺母直接蓋住了。 -coorslight969- ♂ (0 bytes) () 08/04/2023 postreply 17:56:45
• 不好用力,怕把brake fluid reservoir 底座扯斷 -DC_Jeeper- ♂ (0 bytes) () 08/04/2023 postreply 18:06:14
• 有專門拆這種滑牙螺絲的工具的 -老不大- ♂ (0 bytes) () 08/04/2023 postreply 14:09:00
• 多謝各位獻計獻策,折騰半天還是不行,先到此收手了 -DC_Jeeper- ♂ (939 bytes) () 08/04/2023 postreply 16:31:24
• 有一種愛就放手。 哈哈哈 -coorslight969- ♂ (0 bytes) () 08/04/2023 postreply 16:42:33
• 用12 points wrench更容易擰滑 -MoonRiverMe- ♂ (0 bytes) () 08/04/2023 postreply 20:27:48
• 對已經擰壞的螺母來說確實是這樣,6個角的更好 -DC_Jeeper- ♂ (0 bytes) () 08/05/2023 postreply 03:10:05