轎車前後輪之間高度不夠,平時用的Rhino ramps插不進去,不能同時把前後輪開上去。我每次要先倒車把和前輪後輪開上一對矮點的home made wood ramps和正常高度的Rhino ramps, 然後再用Jack把前輪抬高換成後輪一樣高度的Rhino ramps. 結束了再反過來,有點麻煩。誰有更好的妙招?好像有賣low profile car ramps的,價錢還不便宜。
你們修馬車要鑽車底時是怎麽把車架高架平的?
所有跟帖:
•
4個jack stands?用過ramp,結果直接run over,哈哈
-langxing-
♂
(0 bytes)
()
09/24/2022 postreply
10:31:44
•
Jack stands 不如輪子著地安全
-DC_Jeeper-
♂
(216 bytes)
()
09/24/2022 postreply
12:12:51
•
我有一對SUV/pickup用的鐵架,小車用還得加墊2x10 - 其實該用2x12
-chinomango-
♂
(0 bytes)
()
09/24/2022 postreply
12:56:17
•
俺是從中間頂起,3噸的floor jack可以頂起20多寸,底下幹活基本夠用。
-langxing-
♂
(123 bytes)
()
09/24/2022 postreply
18:50:35
•
中間頂起是指一側的中間,還是前後的中間?
-DC_Jeeper-
♂
(123 bytes)
()
09/25/2022 postreply
04:42:56
•
我說的是左右的中間,前麵一個頂點,後麵一個頂點。
-langxing-
♂
(228 bytes)
()
09/25/2022 postreply
10:53:06
•
我第一次用ramp是在車庫裏,開過了,差點撞牆上去了
-ddy-
♂
(0 bytes)
()
09/24/2022 postreply
14:03:56
•
哈哈哈,俺第一次也是over了,看樣子眾多Diyer都走過同一條路
-mountrobson-
♂
(0 bytes)
()
09/25/2022 postreply
18:08:11
•
剛跑到Harbor Freight買了個這東西
-DC_Jeeper-
♂
(237 bytes)
()
09/24/2022 postreply
12:08:21
•
我是先開到2x10上,不敢用塑料的不知何時老化
-chinomango-
♂
(0 bytes)
()
09/24/2022 postreply
12:09:55
•
我倒是想問如何保證ramp不開過頭?
-chinomango-
♂
(0 bytes)
()
09/24/2022 postreply
12:13:55
•
往上開時坡度比較大要加點油門
-DC_Jeeper-
♂
(114 bytes)
()
09/24/2022 postreply
13:04:25
•
我是用上 parking brake, 再往上開。
-TheHawk-
♂
(0 bytes)
()
09/24/2022 postreply
19:01:59
•
切勿這樣操作。
-TBz-
♂
(349 bytes)
()
09/24/2022 postreply
20:29:22
•
謝!
-TheHawk-
♂
(0 bytes)
()
09/25/2022 postreply
15:18:27
•
Low profile ramps是用來加高車身後,方便油壓Jac伸到車下,一般是跑車才用,升那點高度沒其它用處
-khyang86-
♂
(0 bytes)
()
09/24/2022 postreply
12:51:46
•
這正是我的用意
-DC_Jeeper-
♂
(141 bytes)
()
09/24/2022 postreply
13:08:51
•
結果如圖
-DC_Jeeper-
♂
(82 bytes)
()
09/24/2022 postreply
13:12:14
•
RhinoGear?你不是開上去的 - 因為ramp是對立的?
-chinomango-
♂
(0 bytes)
()
09/24/2022 postreply
22:13:25
•
倒車上去,然後再抬車頭把前麵的矮ramp換成高的。方向相對,連wheel chocks都可以不用
-DC_Jeeper-
♂
(0 bytes)
()
09/25/2022 postreply
04:28:56
•
幹脆上auto lift. $3000 應該夠了吧。省下人工買工具。
-PrimeryColor-
♀
(0 bytes)
()
09/24/2022 postreply
15:02:32
•
沒車庫放
-DC_Jeeper-
♂
(0 bytes)
()
09/24/2022 postreply
17:34:09
•
要幹什麽活?非把車子搞平?
-langxing-
♂
(0 bytes)
()
09/24/2022 postreply
15:09:45
•
Transmission fluid, differential fluid,都需要放平.放機油最好也要放平
-DC_Jeeper-
♂
(0 bytes)
()
09/24/2022 postreply
17:36:17
•
友情分享: 用RAMP 的時候,左腳準備在刹車上,右腳踩油門,才不容易過頭。像正常開車那樣,都是右腳,很容易過頭。
-山寺桃花-
♂
(0 bytes)
()
09/24/2022 postreply
18:01:57
•
另外四驅車用岩石模式,跟玩似的輕鬆上RAMP
-山寺桃花-
♂
(0 bytes)
()
09/24/2022 postreply
18:03:18
•
這是個好主意,我的crawl control function 還從來沒用過
-DC_Jeeper-
♂
(0 bytes)
()
09/25/2022 postreply
04:32:03
•
Rhino ramps + 兩Jack stands
-iGarage-
♂
(0 bytes)
()
09/24/2022 postreply
19:51:47
•
前麵有童鞋可能擔心這種有後溜,因為沒有卡後輪
-soccer88-
♂
(0 bytes)
()
09/24/2022 postreply
20:04:53
•
這擔心是多餘的,Ramp上麵有平台。 Jack stand 不可能溜車,除非在坡麵上
-iGarage-
♂
(0 bytes)
()
09/24/2022 postreply
20:39:56
•
這個:Ramp在後輪,至少有Parking brake
-soccer88-
♂
(194 bytes)
()
09/24/2022 postreply
22:14:13
•
Rhino ramps是空心的,安全沒問題?
-chinomango-
♂
(0 bytes)
()
09/24/2022 postreply
22:22:23
•
放心,結實的很,十年以上不放心就換新的
-DC_Jeeper-
♂
(0 bytes)
()
09/25/2022 postreply
04:35:05
•
這樣不容易保持水平,兩對一樣高的ramps在平地上可以確定是水平的
-DC_Jeeper-
♂
(0 bytes)
()
09/25/2022 postreply
09:58:35
•
平地有嗎?通常要排水有斜度的
-chinomango-
♂
(0 bytes)
()
09/25/2022 postreply
21:07:19
•
我用QuickJack 5000 便攜式汽車舉升係統4年多。安全,省事,方便。
-man008-
♂
(0 bytes)
()
09/24/2022 postreply
23:08:17
•
想提這個,就是貴一點點
-soccer88-
♂
(0 bytes)
()
09/25/2022 postreply
00:13:49
•
這個我也覺得危險,方形沒有三角支撐
-chinomango-
♂
(0 bytes)
()
09/25/2022 postreply
08:16:11
•
如果舉起重量還不夠令人信服,請觀看此視頻,了解 QuickJack 實際舉起重量!
-man008-
♂
(715 bytes)
()
09/25/2022 postreply
12:50:42
•
直起沒問題,如果剛好有剪切力或地震呢?沒有利用三角形的穩定性
-chinomango-
♂
(0 bytes)
()
09/25/2022 postreply
21:09:08
•
太占地方,有點笨重
-DC_Jeeper-
♂
(0 bytes)
()
09/25/2022 postreply
09:56:39
•
我是把它放在車庫門後麵。
-man008-
♂
(81 bytes)
()
09/25/2022 postreply
12:43:39
•
讚well organized
-DC_Jeeper-
♂
(0 bytes)
()
09/25/2022 postreply
15:05:51