我的MB CLK350前後輪看上去都是內八字,好像BMW也是設計成這樣的,而且tire tread都是有方向的,後胎比前胎寬,所以前後左右都不能rotate.周末把輪胎卸下來看到磨損非常不均勻,內存快禿了外側還剩很多,馬上準備換了。我的問題是這樣的磨損是設計上導致不可避免的單側磨損,還是我需要做個Alignment了?我這次要選個沒有方向的輪胎,至少左右可以過一段時間rotate一下。
Tire unevenly worn
所有跟帖:
• 前輪內八字是正常的, 不過需要做個Alignment。 -jason1020- ♂ (0 bytes) () 09/07/2021 postreply 13:27:11
• 這種spec估計dealer 比較清楚 -DC_Jeeper- ♂ (95 bytes) () 09/07/2021 postreply 17:32:13
• 這種磨損不正常。 -Oneshotkill- ♂ (0 bytes) () 09/07/2021 postreply 13:29:35
• 所以你也認為alignment有問題? -DC_Jeeper- ♂ (0 bytes) () 09/07/2021 postreply 17:33:45
• 如果沒有改裝過,應該去查查tire alignment,送兩張BMW SAV後輪@30K公裏的照片。 -Oneshotkill- ♂ (178 bytes) () 09/07/2021 postreply 18:25:54
• 你這個看上去磨損正常 -DC_Jeeper- ♂ (0 bytes) () 09/08/2021 postreply 03:14:45
• 前輪toe out 太多也會有這種輪胎磨損。所以還是得去檢查alignment. -覓音- ♂ (0 bytes) () 09/08/2021 postreply 08:44:06
• 運動型車都是負camber,尤其是後輪,所以輪胎內側先磨損 -jwhzzj- ♂ (0 bytes) () 09/07/2021 postreply 14:10:01
• 前後輪都是內側磨損明顯 -DC_Jeeper- ♂ (41 bytes) () 09/07/2021 postreply 17:35:17
• 你得看你的alignment specification -MoonRiverMe- ♂ (189 bytes) () 09/07/2021 postreply 14:12:47
• 沒有查過spec -DC_Jeeper- ♂ (135 bytes) () 09/07/2021 postreply 17:28:06
• 您這是哪個位置的胎? 平時胎壓維持正常嗎? -總要注冊- ♂ (0 bytes) () 09/07/2021 postreply 15:59:45
• 前胎,胎壓一直保持廠家推薦的 -DC_Jeeper- ♂ (47 bytes) () 09/07/2021 postreply 17:29:26
• 那前後兩側胎的內邊都有對等程度的磨損? 應該 -總要注冊- ♂ (119 bytes) () 09/07/2021 postreply 17:58:59
• 對,兩邊磨損程度相同 -DC_Jeeper- ♂ (137 bytes) () 09/07/2021 postreply 18:15:19
• 你找到dealer的話, 他們應該知道原廠的spec, 不會亂來的。 -總要注冊- ♂ (84 bytes) () 09/07/2021 postreply 19:52:38
• 你這staggered胎,肯定是運動配置,alignment指標可能與四方胎不一樣,讓dealer檢查一下吧 -iGarage- ♂ (0 bytes) () 09/07/2021 postreply 17:54:44
• 我先online查一下廠家設置 -DC_Jeeper- ♂ (120 bytes) () 09/07/2021 postreply 18:21:44
• 前胎30psi的建議壓力很有問題。換胎後你前後都打到36 continental 的胎號稱8萬英裏,用8萬公裏應該沒問題吧 -圓老扁- ♂ (0 bytes) () 09/07/2021 postreply 18:53:26
• 查了tire pressure spec -DC_Jeeper- ♂ (126 bytes) () 09/08/2021 postreply 03:23:27
• 說明你載重不夠,空車內8字,載重後就是垂直的。下次裝幾百斤大米壓車, 哈哈 -bushihandyman- ♂ (0 bytes) () 09/08/2021 postreply 07:01:24
• 哈哈,那是是外八字吧?內八字中間越重輪子應該越往內撇 -DC_Jeeper- ♂ (0 bytes) () 09/08/2021 postreply 10:33:22
• 他根本就沒看懂你那原貼,要不就是連小學幾何都沒學會 -MoonRiverMe- ♂ (113 bytes) () 09/08/2021 postreply 11:38:15
• 看看這個壇子裏還有比你更蠢的嗎?哈哈 -bushihandyman- ♂ (0 bytes) () 09/08/2021 postreply 12:15:16
• Everyone knows how stupid you dickhead are -MoonRiverMe- ♂ (171 bytes) () 09/08/2021 postreply 13:05:55
• 不是開玩笑了,你是內8不夠, 正常的都是內8一點點,有重量就垂直了, 不可能外8的 -bushihandyman- ♂ (0 bytes) () 09/08/2021 postreply 12:12:23
• 說說我的例子 -MoonRiverMe- ♂ (250 bytes) () 09/08/2021 postreply 16:48:57
• 謝謝,換胎時我會讓他們仔細查一下 -DC_Jeeper- ♂ (0 bytes) () 09/08/2021 postreply 17:42:51
• 用手使勁壓車頭兩角幾下看得用多大勁兒才能壓下去就知道了 -MoonRiverMe- ♂ (69 bytes) () 09/08/2021 postreply 19:41:41
• 試了懸掛很緊湊 -DC_Jeeper- ♂ (68 bytes) () 09/09/2021 postreply 04:17:47