上次給我的轎車換油時,把前輪開上Rhino ramp換了油,發現有很多舊的油沒有放幹淨,因為底盤是傾斜的。原來給皮卡換油時底盤高,我直接把車前後輪都開上ramp(我有兩對)。現在隻能把ramp放在最前把前輪開上去,或放在最後,把後輪開上去,前後輪中間ground clearance 空間不夠放不下ramp. 前輪抬高以後,後麵尾巴就降低了,沒法用floor jack 在differential 的位置把兩後輪同時抬高再墊ramps,反過來也是一樣。最後我隻能把前輪嫌開上去,然後把後輪一邊頂高了墊上,再去另一邊頂,聽見咯吱響聲,感覺對frame 有扭曲傷害,下次不想這麽幹了,各位大拿是怎麽搞的,有沒有mini ramps, 或者需要自製個矮點的?
給轎車換油時,怎麽讓車保持水平
所有跟帖:
• 不用整個人鑽進去擰放油螺栓吧? -MoonRiverMe- ♂ (92 bytes) () 09/27/2020 postreply 17:10:23
• 不但要,而且油栓位置很別扭 -DC_Jeeper- ♂ (234 bytes) () 09/27/2020 postreply 17:21:52
• 普通的oil drain pan高了點,我用turkey bake pan -MoonRiverMe- ♂ (131 bytes) () 09/27/2020 postreply 17:34:52
• 圖片看不見 -chinomango- ♂ (0 bytes) () 09/27/2020 postreply 18:58:51
• 再貼 -MoonRiverMe- ♂ (88 bytes) () 09/27/2020 postreply 19:26:33
• 烤箱用具 -chinomango- ♂ (0 bytes) () 09/28/2020 postreply 17:25:53
• 放油孔都在裝油盤的後部,好象前輪開上去油放的更多點吧? -iGarage- ♂ (0 bytes) () 09/27/2020 postreply 17:15:34
• 同上。 -indexguy- ♂ (0 bytes) () 09/27/2020 postreply 17:19:26
• 正確的說法是 -MoonRiverMe- ♂ (142 bytes) () 09/27/2020 postreply 17:28:48
• 我的車描述是這樣的 -DC_Jeeper- ♂ (152 bytes) () 09/27/2020 postreply 17:36:51
• 看看這個愚蠢的oil plug設計 -DC_Jeeper- ♂ (325 bytes) () 09/27/2020 postreply 17:32:57
• WTF -MoonRiverMe- ♂ (80 bytes) () 09/27/2020 postreply 17:46:53
• 左前胎放氣不能解決問題 -DC_Jeeper- ♂ (108 bytes) () 09/27/2020 postreply 17:54:38
• 無所謂,反正舊油總有些的,是個稀釋過程。其它fluid也類似。 -chinomango- ♂ (0 bytes) () 09/27/2020 postreply 17:24:03
• 剩的太多,1 Gal以上 -DC_Jeeper- ♂ (59 bytes) () 09/27/2020 postreply 17:39:02
• 裝個Fumoto閥門,手伸過去夠一下 -chinomango- ♂ (0 bytes) () 09/27/2020 postreply 18:30:23
• 1:吸星大法 2:斜坡車道 3:擇機前高或後高, 比如這種情況 -Oneshotkill- ♂ (299 bytes) () 09/27/2020 postreply 17:36:42
• 3是什麽? -DC_Jeeper- ♂ (338 bytes) () 09/27/2020 postreply 17:45:07
• 請推薦個吸油的pump -DC_Jeeper- ♂ (174 bytes) () 09/27/2020 postreply 17:49:13
• 這個不錯,抽幾次就能把最後的一加侖抽出來,Harbor Freight 才$7 -MoonRiverMe- ♂ (168 bytes) () 09/27/2020 postreply 18:18:06
• 看不了圖 -DC_Jeeper- ♂ (0 bytes) () 09/27/2020 postreply 18:39:24
• 重貼 -MoonRiverMe- ♂ (88 bytes) () 09/27/2020 postreply 19:27:03
• 像個小氣筒 -DC_Jeeper- ♂ (23 bytes) () 09/27/2020 postreply 19:43:46
• 我有時油加太多了就用它抽,抽一下就能抽出十幾個CC -MoonRiverMe- ♂ (0 bytes) () 09/27/2020 postreply 19:56:03
• 最早就是Mityvac,現在山寨一大堆 -chinomango- ♂ (0 bytes) () 09/27/2020 postreply 18:33:41
• 謝謝 -DC_Jeeper- ♂ (0 bytes) () 09/27/2020 postreply 18:38:52
• Google “Fumoto oil drain valve”...... -Maddux- ♂ (0 bytes) () 09/27/2020 postreply 18:19:16
• 這個在垂直的oil drain hole上可以 -DC_Jeeper- ♂ (62 bytes) () 09/27/2020 postreply 18:35:36
• Fumoto SX series -2ndGear- ♂ (144 bytes) () 09/28/2020 postreply 04:24:37
• 這個解決了放油的問題 -DC_Jeeper- ♂ (164 bytes) () 09/28/2020 postreply 06:29:13
• 你這情形抽是最簡單的 -MoonRiverMe- ♂ (0 bytes) () 09/28/2020 postreply 08:03:58
• 這個更安全。。。 -slow_quick- ♂ (188 bytes) () 09/28/2020 postreply 08:17:46
• 還是要先解決升高底盤才能卸底下護板 -DC_Jeeper- ♂ (200 bytes) () 09/28/2020 postreply 09:51:50
• 不知道這樣可行不? -TBz- ♂ (420 bytes) () 09/27/2020 postreply 19:33:39
• 這是玩雜技 -DC_Jeeper- ♂ (302 bytes) () 09/28/2020 postreply 05:22:09
• Ramp不會滑動 -TBz- ♂ (228 bytes) () 09/28/2020 postreply 07:12:06
• 即使不動了也要加幾個木頭墊在jack points才敢下去 -DC_Jeeper- ♂ (255 bytes) () 09/28/2020 postreply 08:29:05
• 頂起車頭,前麵兩側用floor jack支撐。開始放油。再頂起車頭,撤去兩側floor Jack,放下車頭。水平。放油結束。 -indexguy- ♂ (0 bytes) () 09/27/2020 postreply 20:08:51
• 放下來時底盤低了 -DC_Jeeper- ♂ (44 bytes) () 09/28/2020 postreply 05:26:39
• Dollar store有一種接油盤,一個手掌高,一美刀一個。 -indexguy- ♂ (0 bytes) () 09/28/2020 postreply 07:00:28
• Why do you need to make your car level -jassco- ♂ (160 bytes) () 09/27/2020 postreply 20:20:42
• don't you check the fluids only when it's level? -MoonRiverMe- ♂ (0 bytes) () 09/27/2020 postreply 20:37:03
• No, I don't. I drained all of the oil I can. Then -jassco- ♂ (175 bytes) () 09/28/2020 postreply 18:47:03
• good luck to yourself -MoonRiverMe- ♂ (0 bytes) () 09/28/2020 postreply 19:08:38
• 我推薦一個吧 -chinomango- ♂ (890 bytes) () 09/27/2020 postreply 20:31:26
• 謝謝,看著不錯 -DC_Jeeper- ♂ (41 bytes) () 09/28/2020 postreply 05:16:49
• 車沒那麽嬌氣吧,多一點舊油死不了的。 -leslieking- ♂ (0 bytes) () 09/30/2020 postreply 21:42:00