05 Sienna. 手冊要求9萬邁換一次。
現在進行式:換正時皮帶和水泵。
所有跟帖:
•
拆雨刷,拆cowl panel.
-indexguy-
♂
(101 bytes)
()
09/09/2020 postreply
05:54:52
•
卸右前輪。拆右側fender apron. 10mm socket.
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
06:27:28
•
歡迎帶圖直播。
-ddy-
♂
(0 bytes)
()
09/09/2020 postreply
07:05:12
•
油管上有關sienna和Lexus 正時皮帶的視頻很多,人家那個才是專業的。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
10:58:02
•
用Ryobi impact wrench 拆曲軸皮帶輪上的螺栓。
-indexguy-
♂
(92 bytes)
()
09/09/2020 postreply
07:06:28
•
balancer pulley needs mark align?
-piper-
♀
(46 bytes)
()
09/09/2020 postreply
07:20:35
•
不明白你的問題,拆crankshaft pulley之前,我做了記號。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
10:59:55
•
放冷卻水。都市傳說:若搞不掂crankshaft 螺栓,你就做不下去了。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
07:26:23
•
impact wrench, 很容易搞定的:)
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
07:29:16
•
或用豐田的一個小專用工具加break bar 也可以
-majhong-
♂
(0 bytes)
()
09/09/2020 postreply
08:06:14
•
那個專門工具隻能用於toyota的車,toyota 新車不用正時皮帶。所以,決定買一個通用的power wrench.
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
11:03:57
•
我是用打火
-chinomango-
♂
(0 bytes)
()
09/28/2020 postreply
19:06:01
•
懇請來圖片
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
07:53:51
•
油管有很多視頻。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
11:05:01
•
不會吧,這是要炸版的架勢啊。
-biglow-
♂
(0 bytes)
()
09/09/2020 postreply
07:52:46
•
Why don’t you wrap him up?
-MoonRiverMe-
♂
(0 bytes)
()
09/09/2020 postreply
09:21:17
•
等他炸完了再卷。
-biglow-
♂
(0 bytes)
()
09/09/2020 postreply
12:51:42
•
拆engine mount(dog bone). 後麵的螺栓是痛點之二。
-indexguy-
♂
(182 bytes)
()
09/09/2020 postreply
07:54:31
•
許多後續的chain引擎,水泵鋁殼與引擎鋁殼連接的10多顆螺絲,貌似沒有鐵螺栓與鋁發生反應的問題。
-老金工-
♂
(0 bytes)
()
09/09/2020 postreply
08:10:26
•
第二代sienna用兩根長鐵螺栓,穿過鋁製X frame. 結果,螺栓生鏽堵死縫細,潤滑油過不去。
-indexguy-
♂
(44 bytes)
()
09/09/2020 postreply
11:19:52
•
拆X frame support. 因為事先灌了不少潤滑油,很容易拿下。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
08:12:23
•
鬆開發電機螺栓,做好記號。鬆了22圈。卸下發電機皮帶。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
08:42:15
•
擰多少圈也要數?擰多緊按一下皮帶不就知道了嗎?
-MoonRiverMe-
♂
(0 bytes)
()
09/09/2020 postreply
09:19:56
•
卸下power steering pump 皮帶。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
08:50:28
•
用租來的pulley puller 卸下crankshaft pulley. 要自己買兩個8mmx1.25 - 70mm的螺栓。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
08:58:42
•
上個茅坑也要向全世界宣布每走一步邁出了左腳還是右腳?
-MoonRiverMe-
♂
(0 bytes)
()
09/09/2020 postreply
09:16:35
•
卸下連接發電機的bracket. 鬆開固定電纜的四個連接件。搞壞最後一個。
-indexguy-
♂
(50 bytes)
()
09/09/2020 postreply
09:54:04
•
卸下底部防塵罩,四個m10螺栓。卸下頂部防塵罩,五個M10螺栓。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
09:57:45
•
看到了正時皮帶,16萬邁後,完好如初。沒有開裂。中盤休息。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
10:24:12
•
見過不少換出的Toyota, Lexus 十幾,二十萬哩的timing belt,狀況都還不錯。水泵則差些。
-iGarage-
♂
(0 bytes)
()
09/09/2020 postreply
11:03:11
•
16萬邁換過火花塞,一點都沒壞。純屬脫了褲子放屁。這次也是這個感覺。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
11:12:35
•
TimingBelt,10萬Mi朝上就是anytime的事情,外觀可能很好。
-老金工-
♂
(0 bytes)
()
09/09/2020 postreply
13:56:16
•
corolla有12萬6斷正時帶的例子
-chinomango-
♂
(0 bytes)
()
09/28/2020 postreply
19:08:51
•
繼續。拆engine mount bottom base. 後麵沉頭的螺栓很難搞。
-indexguy-
♂
(122 bytes)
()
09/09/2020 postreply
11:41:24
•
Lug Nut擰花了 有什麽辦法卸下來嗎
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
12:29:43
•
用小半號的12角 socket 敲進去
-iGarage-
♂
(0 bytes)
()
09/09/2020 postreply
12:40:36
•
多謝!去試試。還有人有別的法子麽
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
12:44:12
•
用impact wrench試試
-violinpiano-
♂
(0 bytes)
()
09/09/2020 postreply
12:52:40
•
也想過去買這種電動的試試,但沒有把握
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:10:02
•
也想過讓修車鋪卸下來再換新的
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:11:11
•
用bolt extractor
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
13:13:31
•
6角的lug nuts怎麽花法?來張圖片看看。你的套筒不也是6
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
13:17:34
•
套筒打滑。手頭無照
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:22:28
•
你換用6邊的套筒就行了
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
13:26:08
•
用的就是六邊套筒。六角Nuts的角化了
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
13:30:29
•
角花了,是因為你用了12邊的套筒,換成6邊的就行了
-piper-
♀
(0 bytes)
()
09/09/2020 postreply
14:10:17
•
沒有用過12邊的。一直用六邊的。可能是上的時候用勁過猛
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
14:24:49
•
用6邊的花了,這得花多大的力。你可以觀察一下套筒裏麵的形狀,
-piper-
♀
(163 bytes)
()
09/09/2020 postreply
15:27:15
•
這個不會錯的
-落城一哥-
♂
(0 bytes)
()
09/09/2020 postreply
15:33:53
•
六角花不罕見,Eric的視頻裏都可看見
-chinomango-
♂
(0 bytes)
()
09/28/2020 postreply
19:11:31
•
lug nut extractor
-biglow-
♂
(0 bytes)
()
09/09/2020 postreply
14:08:13
•
這是其中之一
-落城一哥-
♂
(143 bytes)
()
09/09/2020 postreply
14:23:33
•
那個螺栓的淨空很小,我懷疑bolt extractor 能否裝的上。最重要的是用六邊套筒,套筒完全套入,沒有角度。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
15:10:17
•
bolt extractor 和套筒形狀是一樣的
-piper-
♀
(87 bytes)
()
09/09/2020 postreply
15:29:36
•
看來要買一套。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
17:42:59
•
正時皮帶暴露後,順時針轉直到三個點全部對正。
-indexguy-
♂
(163 bytes)
()
09/09/2020 postreply
13:40:21
•
手冊說,這時應逆時針轉大約60度。這一步爭議很大。我轉了。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
13:42:49
•
拆tensioner 遭到麻煩,前麵一個好拆。後麵一個螺栓套不上套筒,
-indexguy-
♂
(219 bytes)
()
09/09/2020 postreply
13:51:26
•
拆正時皮帶,idler. 下麵那個要用10 mm hex bit socket.
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
14:26:37
•
水泵上有兩根螺栓,要用E-8套筒,網上多人擰斷該螺栓。我不敢用力。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
14:55:26
•
今天到此為止,謝謝大家圍觀。
-indexguy-
♂
(0 bytes)
()
09/09/2020 postreply
14:56:33
•
謝天謝地
-MoonRiverMe-
♂
(0 bytes)
()
09/09/2020 postreply
15:32:27
•
告你一個換timing belt的竅門
-MoonRiverMe-
♂
(346 bytes)
()
09/09/2020 postreply
15:52:19