DIYorDie Techshop, 2099 S 10th St Unit 40, San Jose, Ca 95112, 408.831.1425, book $35/Hr
灣區San Jose DIY修車店提供門吊/工具,每小時35刀,member 30刀
所有跟帖:
• 這個好 -biglow- ♂ (74 bytes) () 05/07/2019 postreply 17:25:26
• 你建一個? -chinomango- ♂ (0 bytes) () 05/08/2019 postreply 20:46:47
• costco 的這個怎麽樣?好像評價還行 -yddad- ♂ (550 bytes) () 05/08/2019 postreply 07:31:01
• 5000 lb 小了點兒,皮卡和大點兒的SUV就沒法用了。 -biglow- ♂ (0 bytes) () 05/08/2019 postreply 08:24:02
• 看網站這個廠家也有7000lb的產品,Costco 現在隻賣5000的,其它地方有 -yddad- ♂ (0 bytes) () 05/08/2019 postreply 09:12:05
• 修皮卡和大 SUV 的哪個零件用這種 lift? -TheHawk- ♂ (126 bytes) () 05/08/2019 postreply 16:19:38
• 花1000塊錢才比我100塊千斤頂把車弄高了3-4吋,覺得有點不值 -2ndGear- ♂ (0 bytes) () 05/08/2019 postreply 09:46:02
• 這個不是差幾寸的事,是安全的問題。 -man008- ♂ (0 bytes) () 05/08/2019 postreply 11:23:31
• 你誤會了,我一直用jack stands的 -2ndGear- ♂ (0 bytes) () 05/08/2019 postreply 14:58:24
• 把車弄高了3-4吋,有時還更難使用工具。 -覓音- ♂ (0 bytes) () 05/08/2019 postreply 12:27:56
• 它有兩個高度可用。 -man008- ♂ (0 bytes) () 05/08/2019 postreply 12:40:41
• 男八號也推薦過,對於底盤比較低的轎車,特別是保養維修頻率較高的寶馬車主非常適用,效率/高度/水平都兼顧到了! -Oneshotkill- ♂ (0 bytes) () 05/08/2019 postreply 10:45:03
• 大麻國好市多CA$1350/5000lb,$1500/7000lb折算成燈塔刀還是比較合理。 -Oneshotkill- ♂ (87 bytes) () 05/08/2019 postreply 11:11:30
• 一點貴。 -man008- ♂ (745 bytes) () 05/08/2019 postreply 12:37:12
• 底盤低的我是先墊1.5”木以便看floor joint定位;再用高ramp加木板減緩斜度 -chinomango- ♂ (0 bytes) () 05/09/2019 postreply 12:40:30
• 看起來不怎麽牢靠 -MoonRiverMe- ♂ (0 bytes) () 05/08/2019 postreply 20:09:22
• 這個中國造出過事故的 -chinomango- ♂ (0 bytes) () 05/08/2019 postreply 20:46:12