油泵卸不下來買了個專門工具結果把三個小塑料片都給掰斷了,還是下不來,還有法嗎
所有跟帖:
• 斷電斷保險,開油箱蓋降壓,拆油管和電纜,工具箱有這個的話也可以試試運氣,Good luck! -Oneshotkill- ♂ (163 bytes) () 03/29/2019 postreply 09:05:16
• 你那個專用工具我是買不起,大榔頭加改錐伺候感覺就像要拔牙。。。拔。。。牙!:-DDD -Oneshotkill- ♂ (0 bytes) () 03/29/2019 postreply 09:36:03
• 找了兩個拔牙大法 -Oneshotkill- ♂ (238 bytes) () 03/29/2019 postreply 11:32:57
• 明天試試,謝謝 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 13:55:55
• 他那地方沒那個空間用你這個 -MoonRiverMe- ♂ (67 bytes) () 03/29/2019 postreply 18:53:48
• Never try, Never know. -Oneshotkill- ♂ (543 bytes) () 03/29/2019 postreply 19:23:22
• 用過這東西,一定要轉一個很大的角度才能勒緊 -MoonRiverMe- ♂ (74 bytes) () 03/29/2019 postreply 20:57:31
• 要換我的話就澆熱水加木棍頂著敲 -MoonRiverMe- ♂ (0 bytes) () 03/29/2019 postreply 21:00:24
• 就不能多說兩句? -MoonRiverMe- ♂ (218 bytes) () 03/29/2019 postreply 09:12:38
• 將加了圖片在上麵你可以看見那三個被掰斷的塑料牙齒 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 09:58:56
• 噴點潤滑液,肥皂水也行。然後用扁頭螺絲刀卡在邊沿凸起,用1斤大小錘子敲螺絲刀頭部 -needtime- ♂ (83 bytes) () 03/29/2019 postreply 09:19:53
• 用大螺絲刀沿逆時針方向敲。 -覓音- ♂ (0 bytes) () 03/29/2019 postreply 09:26:18
• 我還用500lbs impact driver試過 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 10:02:54
• 大部分衝力被你那個塑料片子吸收掉了,沒用的。 -needtime- ♂ (50 bytes) () 03/29/2019 postreply 11:05:43
• 受力點應該放在塑料片的根部 -MoonRiverMe- ♂ (23 bytes) () 03/30/2019 postreply 10:53:41
• 你們上麵所說的步驟我都做了,除沒有用oneshotkill的這個工具和沒有噴潤滑劑外 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 09:57:51
• 因為卸不下來又把管線給裝了回去 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 10:00:02
• 按各位大師的建議清理幹淨,比如WD40,然後再試試你的工具? -hellotom- ♂ (277 bytes) () 03/29/2019 postreply 11:19:15
• 看過工具也是一樣的就是擺不動 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 12:17:41
• 你試過在塑料環一圈噴過WD40或PB Blaster, 然後等上半個小時,再用你的工具嗎? -hellotom- ♂ (255 bytes) () 03/29/2019 postreply 13:32:04
• 工具卡在塑料牙上在用breaker bar. 加長鐵管,今晚上噴上pb blaster的明天再試 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 15:07:42
• 希望之前該車的fuel pump沒有人動過。應該用不到加長鐵管。3/8的brakerbar應該夠用了。 -hellotom- ♂ (536 bytes) () 03/29/2019 postreply 15:44:00
• 一手新車,沒人動過,手冊上對上起點,擰兩輪,我這個是多擰了一點點,過了哪個起點 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 21:11:20
• 一手車應該相對容易一些。盡量把螺口清理幹淨。還有操作的天氣溫度。天太冷,部件冷縮也是障礙。 -hellotom- ♂ (431 bytes) () 03/30/2019 postreply 14:35:34
• 是啊,說不定油泵是好的,電路有問題啊,麻煩你看看這個圖,1隻有在crank時才有9V電壓,在ON的時候沒有,這正常嗎? -ddy- ♂ (87 bytes) () 03/30/2019 postreply 20:05:59
• 沒看懂,樓主惜字。不是一圈幾個螺絲嗎? -chinomango- ♂ (0 bytes) () 03/29/2019 postreply 10:10:51
• 不是螺絲,是瓶蓋子 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 10:42:59
• 木頭做個工具,底麵凸塊卡各個凹槽,上麵方柄擰 -chinomango- ♂ (47 bytes) () 03/29/2019 postreply 20:21:24
• 噴點潤滑劑再用熱分槍加熱軟化一下塑料可以嗎 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 10:57:06
• 如果螺紋是膠住的(比如用了loctite),hotgun有幫助,但注意這是汽油箱,切忌放幹油再幹。 -傻悶登兒- ♂ (0 bytes) () 03/29/2019 postreply 11:15:07
• 澆灌開水可以,澆蓋子下麵的殼體 -chinomango- ♂ (0 bytes) () 03/29/2019 postreply 20:22:58
• 不懂,瞎建議: -傻悶登兒- ♂ (701 bytes) () 03/29/2019 postreply 11:03:09
• 工具和方法是關鍵。先查打開這個的正確方法,再找工具。不要野蠻施工。 -傻悶登兒- ♂ (0 bytes) () 03/29/2019 postreply 11:05:10
• 這個視頻講得很清楚(2010 corolla), 看起來並不難。 -傻悶登兒- ♂ (212 bytes) () 03/29/2019 postreply 11:29:57
• 動手前看過這個好幾遍,他的很容易,我都不知道怎麽這麽難 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 11:56:47
• 打不開才根據手冊買了這個工具 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 11:58:42
• 你沒有擰/敲反方向吧?看得出這個就是反時針擰,你的可能咬合得太死。先把所有連線拆掉,然後用俺說的後麵那種channel lock -傻悶登兒- ♂ (82 bytes) () 03/29/2019 postreply 12:36:25
• 絕對沒反是逆時針方向,在實在擰不動的時候,我還試著順時針方向擰了一下也一點不動 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 12:44:13
• 如果你那幾根cables都拆了還敲不動,說不定你這個上過膠?或者天氣過熱變形了。那樣就隻有毀掉換整個assembly. -傻悶登兒- ♂ (338 bytes) () 03/29/2019 postreply 12:56:16
• 我擰的時候那些管線都給拆了,用了breaker bar 再加一根長鐵管 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 14:02:02
• 那就奇了。 -傻悶登兒- ♂ (0 bytes) () 03/29/2019 postreply 14:32:19
• 能把那塑料牙都給掰斷了,這力量應該不小吧 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 15:04:44
• 沒道理上膠,因為下麵隻是一個o ring -ddy- ♂ (0 bytes) () 03/29/2019 postreply 14:03:53
• 天冷,殼體是金屬吧?收縮比塑料厲害 -chinomango- ♂ (0 bytes) () 03/29/2019 postreply 20:34:18
• 實在不行就把蓋子銼掉。買個新蓋應該不貴吧? -覓音- ♂ (0 bytes) () 03/29/2019 postreply 11:24:26
• 這個比較難關鍵是怕把裏麵的油箱搞壞 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 12:02:30
• 提供一個工具的鏈接,HD or HF最好。網上的太費時間,謝謝 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 15:12:48
• 塑料老化,你看看這個有沒有幫助 -langxing- ♂ (212 bytes) () 03/29/2019 postreply 12:16:58
• 這個視頻倒沒看過但買工具之前我試過這個辦法,不行,沒那個工具好 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 12:20:24
• 試試用橡皮錘子敲敲蓋子,如果是粘上了,希望能給敲鬆動,然後再擰 -langxing- ♂ (0 bytes) () 03/29/2019 postreply 13:16:50
• 好,明天試試 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 14:04:32
• 最壞的情況,用dremel tool 小心的把外圓塑料圈鋸開,卸下來。通常新泵會給新的塑料圈 -dvdport- ♀ (125 bytes) () 03/29/2019 postreply 14:27:58
• 要$30-$40單買,聊勝於無吧。 -Oneshotkill- ♂ (87 bytes) () 03/29/2019 postreply 14:49:35
• 要是沒有辦法就隻能這樣了,關鍵是我怕把裏麵的瓶口搞壞了 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 14:57:47
• 東西就是oneshotkill給的圖,你給個工具鏈接,提供一下你的意見,我琢磨琢磨 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 14:59:56
• 請大家不吝提供各種方法包括破壞方法,如可能請提供一些你認為重要的操作細節,謝謝啦 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 15:18:51
• 如果已經用你的工具, 中間加6角螺絲, 加套筒, 500磅衝擊槍, 還是不行的話, 估計隻有破壞這一方法了。火攻太危險。 -PrimeryColor- ♀ (0 bytes) () 03/29/2019 postreply 18:01:39
• 工具是3/8的我用了一個3/8轉1/2,然後用break bar 加長/impact driver -ddy- ♂ (0 bytes) () 03/29/2019 postreply 18:18:26
• 反正是死馬, 這一招應當行。 -PrimeryColor- ♀ (142 bytes) () 03/29/2019 postreply 21:45:14
• 有一餿主意, 用幹冰或冰塊冷卻塑料。塑料的膨脹係數遠大於金屬。 -PrimeryColor- ♀ (0 bytes) () 03/29/2019 postreply 18:08:46
• 今上午幹活的時候氣溫隻有38度,覺得冷的時候這個塑料更硬很難弄 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 18:15:51
• 絕不能用火,熱風槍沒準可以但是不要吹蓋子吹下麵body能夠著嗎? -chinomango- ♂ (0 bytes) () 03/29/2019 postreply 20:32:05
• 太陽下暴曬後, 提高金屬溫度。原來溫度如此低, 怪不得打不開。 等到夏天肯定很容易。 -PrimeryColor- ♀ (176 bytes) () 03/29/2019 postreply 21:47:24
• 今晚從上麵噴了PB blaster,兩個人從兩邊用板手,板手+木棍(隻有一根棍)錘了至少20分鍾,沒用,明天再試。 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 21:19:49
• 空間太小,沒法從下麵噴。 -ddy- ♂ (0 bytes) () 03/29/2019 postreply 21:21:01
• 準備上這個家夥 -ddy- ♂ (136 bytes) () 03/29/2019 postreply 22:18:30
• 好一點, 一樣原理。 關鍵是解決接觸點的非剛性接觸。故建議用 epoxy 膠住。 -PrimeryColor- ♀ (20 bytes) () 03/30/2019 postreply 08:43:25
• 再試一把,不行就送出去了 -ddy- ♂ (0 bytes) () 03/30/2019 postreply 18:12:37
• 可能沒把握技巧,盡下死力了 -ddy- ♂ (0 bytes) () 03/30/2019 postreply 19:41:24
• 這裏是流程,試一試這個扳手 -soccer88- ♂ (212 bytes) () 03/30/2019 postreply 08:26:02
• 這個哥們的口音很有趣。Fire 是 Fire. Wire 也是 Fire. Video質量相當好。 -老九不能走- ♂ (0 bytes) () 03/30/2019 postreply 10:11:31
• Toyota: How to remove the ring. 注意安全 -soccer88- ♂ (1229 bytes) () 03/30/2019 postreply 08:30:19