Alignment問題

換完減震器要不要做Alignment.

下麵是我剛搜的。減震器拆了又裝，我也沒看見在哪做camber,caster。我知道toe是調方向杆。

原來就根本沒地方調，唯一能做的就是鬆了上麵的四個螺絲轉轉。

 

Usually Camber and Caster can only be minimally adjusted on FWD. The only way you could do it is removing the outer 4 strut mount bolts, jack the control arms up and rotate the strut 90 degrees of a turn at a time and watch the monitor if it gets any closer to the right spec. I think you could only turn it 4 times until it goes back to where it was before alignment, not much of a difference. If there is excessive angle out of alignment, then something must been bent or somebody moved the cradle of the engine bay when they worked on it.

所有跟帖： 

• MoonRiverMe,你給我出來 -窮則思變- ♀ (34 bytes) () 09/01/2014 postreply 11:28:24

• 這樣不好。大家在這裏都是依自己的經驗幫助別人，都會有對有錯。嚴格說， -史迷- ♂ (794 bytes) () 09/01/2014 postreply 11:59:46

• 95 mazda 626 -窮則思變- ♀ (51 bytes) () 09/01/2014 postreply 12:24:16

• 看我下麵的回帖。我不調，因為沒設備；但照舊樣裝回。所以，一開始我就問你這個事。 -史迷- ♂ (139 bytes) () 09/01/2014 postreply 12:48:09

• 我估計和原樣差點， -窮則思變- ♀ (98 bytes) () 09/01/2014 postreply 13:57:19

• Now watch your language -MoonRiverMe- ♂ (803 bytes) () 09/01/2014 postreply 13:04:17

• Hey, easy -窮則思變- ♀ (341 bytes) () 09/01/2014 postreply 13:46:43

• How polite this was：“你給我出來，” -MoonRiverMe- ♂ (562 bytes) () 09/02/2014 postreply 13:00:39

• You never know who wrote this -MoonRiverMe- ♂ (216 bytes) () 09/01/2014 postreply 11:36:15

• 有些車可調，有些車不可調。 我上次為了這問題，訪問了專業人， 請看： -zhang88- ♂ (290 bytes) () 09/01/2014 postreply 12:08:47

• 非常清楚了, 謝謝。 -我胡說八道- ♂ (0 bytes) () 09/01/2014 postreply 13:39:49

• Hope this is the answer -窮則思變- ♀ (209 bytes) () 09/01/2014 postreply 12:17:03

• 俺怎麽覺得這麽轉一下和不轉沒區別呢？ -窮則思變- ♀ (99 bytes) () 09/01/2014 postreply 12:30:45

• 這就對了。這就是我第二個回帖裏提及的在上麵mount 裏的“偏心”。別小看這九十度的轉啊， -史迷- ♂ (410 bytes) () 09/01/2014 postreply 12:44:13

• 這九十度這麽重要？ -窮則思變- ♀ (39 bytes) () 09/01/2014 postreply 13:51:11

• alignment非一般修車店都能做，校正不好越調越偏，你想自己毀啊？ -obamacome- ♀ (0 bytes) () 09/01/2014 postreply 13:04:43

• 說話注意點，網友都是想幫你。moonriverme 說的對，換了struts -山裏人- ♂ (437 bytes) () 09/01/2014 postreply 13:56:13