紙上談兵而已,非本人撰寫操作,僅供參考!
Hi all, I recently picked up a 2006 IS350, however the seller only had one remote to the car.
So I ordered two additional new Smart Card key to register to the car through the use of the "aftermarket" M-VCI cable.
Please keep in mind, there is no way to program used keys/cards without additional expensive hardware/software.
So these steps only work for brand new never been programmed cards/keys.
:: DISCLAIMER ::
These instructions are provided as a reference for you to refer to adding additional remotes to the car.
These procedures worked on my vehicle, however your miles may vary, therefore, I am, in no way, responsible for any damages caused in the process.
Please do not continue reading if you do not agree!
Stuffs you will need:
(1) - NEW, never programmed , Smart Card Key (parts # 89904-50641)
(1) - 32-bit Windows XP/7 laptop with Toyota Techstream installed
(1) - M-VCI USB to ODBII Cable with 32-bit drivers installed
(1) - Original programmed remote for the procedures
This is how a brand new, never programmed, found on eBay.
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/FoMoX.jpg)
This is all the stuffs you need in order to program the key:
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/r2aGi.jpg)
Location of the OBDII plug, it is right above the brake pedal with a black cover
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/R5BMg.jpg)
Run Techstream, and click on "Connect to vehicle"
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/1fsa1.png)
After initialising, this will show up, pick OTHER if you do not have radar cruise, then press next
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/aH3Sj.png)
Then double click on Smart Access
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/syewJ.png)
Then click on "Utility" on the left hand side
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/AD5zQ.png)
Then click on "Smart Code Registration"
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/sLK1l.png)
Then check all the boxes and press next,
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/wyqlx.png)
Then Techstream will inform you how many slots are available and taken,
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/2mojJ.png)
Then Techstream will inform you to place both new and programmed remotes outside of the vehicle. Press next
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/DtAt0.png)
When you are ready, press Pre-Start CHK to enable the Start box, and quickly tap the registered remote to the ignition botton in the vehicle with the L logo facing it.
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/otnZA.png)
Then quickly place the original remote outside of the vehicle and tap the smart card to the ignition button
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/F4gVA.png)
Lastly, congratulations, you have successfully programmed the smart card to the system
![Click the image to open in full size. Click the image to open in full size.](http://i.imgur.com/w6Z4j.png)
Read more: http://www.clublexus.com/forums/is-second-generation/661037-just-added-another-smart-card-key-to-the-car-diy-instructions-included.html#ixzz368Gyzkdo