想換掉舊的後院的水龍頭,擰了半天下不來。請問那個螺絲扣是在哪個位置?
在下圖中的綠圈裏,還是左邊的藍圈下?奇怪的是,綠圈裏還有個繡的螺釘。謝謝。
想換掉舊的後院的水龍頭,擰了半天下不來。請問那個螺絲扣是在哪個位置?
在下圖中的綠圈裏,還是左邊的藍圈下?奇怪的是,綠圈裏還有個繡的螺釘。謝謝。
• 這樣挺好看的,不用換。 -烹小閑- ♀ (0 bytes) () 02/06/2023 postreply 12:37:12
• 問題是老滴水,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:38:33
• 拚多多上買一個專門接在水龍頭上的延伸管完美解決問題 -9876543- ♀ (0 bytes) () 02/06/2023 postreply 13:04:32
• 哈哈哈哈,古香古色 -seattleWA- ♀ (0 bytes) () 02/06/2023 postreply 12:40:13
• 古道流水 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:25:33
• 切割換整體,後麵的銅管一起換了 -百鳥朝鳳- ♂ (0 bytes) () 02/06/2023 postreply 12:41:10
• 不願意費那麽大勁,還得鑿牆,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:44:31
• 這個應該是很老的(40+),現在都是銅的,包括管子;你看看能不能換墊圈 -胡雪鹽8- ♂ (194 bytes) () 02/06/2023 postreply 12:41:21
• 如果是銅的是用錫焊上去的 -胡雪鹽8- ♂ (0 bytes) () 02/06/2023 postreply 12:42:53
• 年輕些20+。墊圈那個也難擰,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:43:28
• 如果是20+還嫩,這樣換;好像和你的一樣 -胡雪鹽8- ♂ (194 bytes) () 02/06/2023 postreply 12:47:38
• 啊哈,應該就是這個了! -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:58:45
• 有一些技術難度,建議找水管工;如果自己搞有問題問我 -胡雪鹽8- ♂ (0 bytes) () 02/06/2023 postreply 13:06:52
• 好! -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:26:25
• 那個也擰不動,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:45:17
• 好吧,過幾天找個更大的扳手再叫鄰居,,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:51:14
• this.. -borisg- ♂ (344 bytes) () 02/06/2023 postreply 12:43:05
• 我買了個這樣的,但不知道舊的時分也這樣,,,,因為大鉗子都擰不動 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:46:44
• 感覺你這是古董,不用做舊,留著觀賞 -小白和你拚了- ♀ (0 bytes) () 02/06/2023 postreply 12:43:22
• 我想取下來放屋裏觀賞,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:47:47
• 應該都有. 先上油或wd40去下鏽再擰. 不行用焊槍燒燒, 敲打幾下. -輕輕的我來- ♂ (0 bytes) () 02/06/2023 postreply 12:43:45
• 你說的我都試了,,,可能火力不夠,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:48:58
• 最好燒紅了, 多試兩次. -輕輕的我來- ♂ (0 bytes) () 02/06/2023 postreply 12:55:22
• 好吧,我上次沒敢使勁燒,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:20:07
• 得鋸掉接新管子 -oops_yz- ♀ (0 bytes) () 02/06/2023 postreply 12:45:21
• 那太費事了,,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:50:15
• 會不會是銀焊? -Duckmaster- ♂ (0 bytes) () 02/06/2023 postreply 12:47:26
• 不懂啊,沒聽說過,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:51:43
• 看到螺紋了嗎?要沒看到,是直接焊接的 -Duckmaster- ♂ (0 bytes) () 02/06/2023 postreply 12:52:57
• 明白了,就是悍的,從沒知道過這個! -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:59:38
• 水龍頭不可能焊上去 -xiangbuming- ♂ (0 bytes) () 02/06/2023 postreply 13:02:12
• 以前我也這樣認為,,,看上麵視頻 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:03:51
• 見過有人用一種噴的東西能除鏽 還有是拿錘子砸鬆了用板手 -銅鑼燒- ♂ (0 bytes) () 02/06/2023 postreply 12:49:47
• 我查視頻也看到過,,,,蠻力啊 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 12:52:38
• 我覺得擰不下來的,無論哪個位置 -蒙娜麗莎- ♀ (0 bytes) () 02/06/2023 postreply 12:52:41
• 你覺得太對了! -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:00:10
• 你這個太老了,看看裏麵有沒有可以擰掉的地方,如果沒有就鋸掉,replace新的,有工具應該不難 -一笑拉- ♀ (194 bytes) () 02/06/2023 postreply 12:52:45
• 看來多半這樣,就是剩餘管太短了,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:01:35
• 把功課做足了再做,要不然會很麻煩,看有沒有可以接一節水管的可能 -一笑拉- ♀ (0 bytes) () 02/06/2023 postreply 13:03:17
• 好,我先謝過各位師傅了,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:05:50
• 兩個地方都是螺口,但是綠圈的地方沒法擰。你需要兩個大號管扳子 -xiangbuming- ♂ (0 bytes) () 02/06/2023 postreply 12:55:26
• 現在看來是焊的了,,,我準備火烤 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:02:50
• 用牙咬 -LexusOnly- ♂ (0 bytes) () 02/06/2023 postreply 12:59:55
• 找李大牙 -午後陽光亮- ♀ (0 bytes) () 02/06/2023 postreply 13:02:39
• 我可以咬裏麵的皮墊,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:04:56
• 你這個不就是院子裏澆花的管子嗎?不常用跟本不值得費事,拚多多有賣延長管的,一巴掌長,套上就止住滴水了 -9876543- ♀ (0 bytes) () 02/06/2023 postreply 13:13:09
• 類似這個,$2 塊錢 -9876543- ♀ (81 bytes) () 02/06/2023 postreply 13:14:54
• 嗯 這倒是個替代的絕妙主意,,,, -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:19:24
• 你把照片給賣家看,她們會推薦合適的size,這種套上就不會滴水了,用著也很方便 -9876543- ♀ (0 bytes) () 02/06/2023 postreply 13:20:53
• 你可以裝個這個,還可以接管子 -胡雪鹽8- ♂ (1075 bytes) () 02/06/2023 postreply 13:26:14
• 你和小九都聰明 哈哈 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:36:39
• 你能不能先把螺絲鬆一下,再由綠圈處試一下。另外valve上三個字母是什麽。ABP? -temptemp- ♀ (0 bytes) () 02/06/2023 postreply 13:23:17
• 螺釘繡了 回頭我再清理了再看仔細再試 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 13:31:34
• ABP? 我網上粗查了一下,ABP接口好像在你綠圈處。 -temptemp- ♀ (0 bytes) () 02/06/2023 postreply 13:35:02
• 最省事就是從綠圈處鋸斷,重新焊一個有陽螺紋的接頭,再擰個新龍頭上去 -天蠶- ♂ (72 bytes) () 02/06/2023 postreply 13:39:08
• 離牆太近,不好焊。 -temptemp- ♀ (0 bytes) () 02/06/2023 postreply 13:49:48
• 有一寸的出頭就可以了 -天蠶- ♂ (0 bytes) () 02/06/2023 postreply 13:51:23
• 1/2" brass pipe outside diameter is 0.84". 從照片看,長度小於直徑,1/2“吧 -temptemp- ♀ (0 bytes) () 02/06/2023 postreply 13:57:32
• 那就隻好用牙咬了 -天蠶- ♂ (0 bytes) () 02/06/2023 postreply 14:08:36
• 你們 哈哈 都是行家。我認真思考一下 -李大牙- ♂ (0 bytes) () 02/06/2023 postreply 14:13:05
• 工欲善其事必先利其器,晚上磨牙先 -天蠶- ♂ (0 bytes) () 02/06/2023 postreply 14:15:57
• 這好像也解釋了螺釘的存在。有人偷懶。 -temptemp- ♀ (0 bytes) () 02/06/2023 postreply 14:22:15