想更換這個2個MIC IC,可是不知道怎麽下手?
一般的電烙鐵根本無法操作,用HEAT GUN又怕傷了周圍的原件。
謝謝!!!
各位大蝦,幫俺看看,該怎麽下手?真叫人有點抓狂!
所有跟帖:
•
用細銅絲線墊在烙鐵下麵加熱,銅絲會吸收焊錫
-滋鄂-
♂
(0 bytes)
()
12/10/2014 postreply
20:23:15
•
弄個吸錫器好像不是什麽大不了的事情吧?
-biglow-
♂
(0 bytes)
()
12/10/2014 postreply
20:26:00
•
沒玩過吧?取下有專用頭,焊上用扁頭就行了(見內)。油管上也有
-味苦-
♂
(138 bytes)
()
12/10/2014 postreply
21:18:37
•
用錫紙剪個洞,露出要拆的芯片,其他用錫紙包嚴了。然後用heatgun吹兩三分鍾就下來了。
-追風大老虎-
♀
(0 bytes)
()
12/10/2014 postreply
21:37:55
•
專業地是用棕色的耐熱透明膠帶粘蓋周邊元件,錫紙麵大了會散熱多
-obamacome-
♀
(0 bytes)
()
12/12/2014 postreply
20:00:23
•
google solder wick
-lovecorn-
♂
(0 bytes)
()
12/10/2014 postreply
21:38:50
•
even easier, cut it.
-lovecorn-
♂
(14 bytes)
()
12/10/2014 postreply
21:40:08
•
you may damage the solder pad
-US_CAR.-
♂
(0 bytes)
()
12/10/2014 postreply
22:10:56
•
這個問題我可以回答:
-US_CAR.-
♂
(1466 bytes)
()
12/10/2014 postreply
22:10:05
•
茅台也行,嗬嗬, 周末喝酒啦。
-墨西哥-
♂
(0 bytes)
()
12/12/2014 postreply
09:29:30
•
以前沒有專用工具時,都是用cutter把IC夾碎。如果不敢來硬的,可用大量的焊錫當導熱體,先把一邊焊開(IC下用刀片頂一下),然
-coolwin-
♀
(0 bytes)
()
12/10/2014 postreply
23:02:23
•
直插式的穿孔元件可以這樣做,但表麵貼元件一夾就把PCB上的焊盤弄壞了,不能這麽蠻幹。
-US_CAR.-
♂
(0 bytes)
()
12/10/2014 postreply
23:33:53
•
先示範方法2: 焊錫群毆。
-coolwin-
♀
(1316 bytes)
()
12/12/2014 postreply
18:20:59
•
當然用蠻力的用力太小,方向和從什麽地方開刀,得幹廢N塊板子才能悟出來。但上麵這方法無論生手熟手,基本上都能成功。
-coolwin-
♀
(0 bytes)
()
12/12/2014 postreply
18:34:33
•
用與芯片排腳等寬的厚紫銅皮卷在烙鐵上,自製個扁平頭,瓦數及烙鐵頭太小不行
-obamacome-
♀
(79 bytes)
()
12/12/2014 postreply
19:30:45
•
謝謝樓上的各位大蝦。solution找到,報告一蛤。。。
-我愛北京大前門-
♂
(158 bytes)
()
12/11/2014 postreply
08:34:08
•
這個要出事的。質量太差
-味苦-
♂
(0 bytes)
()
12/11/2014 postreply
16:07:20
•
按滋鄂的做,Fry's有吸錫 的銅編織帶。
-chinomango-
♂
(0 bytes)
()
12/11/2014 postreply
08:48:45
•
若heatgun出風口太大,用罐頭盒鐵皮彎個遮風嘴套住吹,取下貼上芯片都能用,視頻上的風口太小
-obamacome-
♀
(0 bytes)
()
12/12/2014 postreply
19:21:01
•
這個專業一些,需要rework gun+rework tape.我這裏是技術員做這個事。
-soccer88-
♂
(116 bytes)
()
12/14/2014 postreply
03:48:11
•
我工作這裏天天有這個活,嘿嘿
-soccer88-
♂
(0 bytes)
()
12/14/2014 postreply
03:49:27
•
這有pin的好弄,滋鄂 說的對啊。 或用尖頭的羅鐵 一個一個pin 加熱 翹起
-130131-
♂
(0 bytes)
()
12/15/2014 postreply
09:36:35
•
我也做過這活兒。
-130131-
♂
(0 bytes)
()
12/15/2014 postreply
09:37:15